Fiat 500 Replacement Key Fob

If your 500 remote key fob has stopped working, it's time to replace the battery. However, if you replace the battery and it doesn't work it is likely to be elsewhere.

At United Locksmith, we specialize in making new keys for classic automobiles. We have the tools and components needed for this service.

Dead Coin Battery

A dead battery is the primary cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob has the battery of a coin-cell which will quickly drain when it isn't utilized frequently enough. If your remote started to show signs of weakness such as a loss in range or stopped working completely the battery could be dead.

The battery inside the key fob is held in place by metal retaining clips. If the clips aren't tightly secured, they could result in problems with contact that can prevent the remote from receiving power. Use a flathead screwdriver to break open the retaining clip and remove the old battery. Be sure to use an alternative battery that has the same type of voltage, size and specifications as the original battery.

The key fob might also be damaged or corroded due to exposure to water. Even a small bath in soapy water can harm the electronic chip within. Make sure your key fob is dry.

Water Damage

Water damage could be the cause of your key fob not working properly. The rubber seals on key fobs prevent them from getting damaged by a slight drizzle or splash of water. However, it is essential to keep the keys out of the washing machine, the ocean and pool.

The key fob is equipped with an electronic chip in it that sends a signal car's immobilizer system. The chip is what allows the 500 to start and lock. If it gets wet, however it will cease to work.

If you're looking to determine if your key fob is functioning it is possible to clean the internal electronics using isopropyl or an electronic cleaner. However, it's recommended to purchase a replacement from a dealer instead of trying to repair the key fob which has been submerged by salt water.

A Replacement Key For fiat punto key programming Ducato Van (Https://Thomasleg2.Bravejournal.Net) fob may cost you a little bit however, it's cheaper than having to have your Fiat 500 towed to a dealer and repaired there! You could also do it yourself by following some simple steps. Be sure to have the correct battery type before you attempt to open your keyfob. You can find step-bystep instructions for any car keyfob on the internet.

Faulty Chip

The chip inside the key fob communicates with the immobiliser of your car to ensure that your vehicle will only start once the correct locked keys in car boot fiat punto are used. If the chip is damaged or damaged the car will not start regardless of what you do.

A chip that is damaged can happen due to several reasons, but most often it is due to water damage or a dead battery. It is best to leave the repair to a professional locksmith who will be able to replace the chip in a short time and at a an affordable price.

If your key fob ceases to function after exposure to clean tap water or rain, take out the battery and wipe down the electronic component with a paper towel to ensure it's dry before putting it back in. If the key fob does not work it's probably an issue with the chip and will need to be replaced.

Some people will go to their dealer when they are in need of an entirely new Fiat key fob, however this can be a very costly alternative. United Locksmith is the best place to go if you want your Fiat keyfob fixed at a reasonable price. We have the tools and experience required to repair your Fiat key fob in a timely and professional manner.

Faulty Receiver Module

fiat 500 spare key key fobs transmit a signal to the vehicle that can unlock and lock doors (and start the vehicle for those with an automatic transmission) up to 50 feet. However there are a few things that can cause the fob to stop working. This includes a dead coin battery water damage, worn buttons or a problem with the receiver module or signal interference, or an electronic chip that is malfunctioning.

If the fob is in the pocket that has been subject to severe trauma (such as being dropped onto the floor or washed in the washer) it might not be able to communicate with the Body Control Module (BCM) of the car. The BCM is a security device which will only accept signals from genuine keys.

You will need to replace the fob if this happens. A professional locksmith can take care of all aspects of the replacement procedure and even program a new one for your 500. In fact, they can even provide you with a clone key that functions exactly the same as your original fob (and costs a fraction of the price).