Reasons Your fiat 500 replacement remote key cost 500 Key Fob Won't Work

A key fob from fiat 500 spare key cut 500 is a great way to unlock the doors and start the car. There are many reasons the fob won't work. This could be due to a dead coin-battery water damage, problems with receiver modules, as well as interference.

This listing is for a NEW replacement fiat key cutting Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob will not function is an inactive battery. Modern key fobs offer only a limited range of operation and must be within just a few inches of the vehicle in order to function. If you are not within your vehicle, and you push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) with a new battery of a trusted brand such as Panasonic Duracell or Energizer. They are usually available in your local hardware store, or online.

You can test the battery of your coin-cell by pressing the buttons while you are standing close to your fiat 500 new key cost uk punto car key; 4dagu.com, 500. The car should flash its parking lights and the key fob will operate the lock and unlock buttons.

If the key fob won't function after replacing the battery, it may have water damage that prevents it from communicating with the receiver module in your car. Water damage can occur through a variety of methods, including a simple splash or submerging your key fob in saltwater at the beach. If you suspect that your fob has been exposed to water, you can try placing it in a dry rice bag to draw the moisture out. If this doesn't work, you will have to get your fob reset by an auto locksmith or a dealer.

Water Damage

While the fob comes with rubber seals that keep water out of the chip's electronic circuit it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater is especially dangerous to the fob's circuit board, causing it to short out and eventually die. It's not a good idea to submerge the fob in water however, don't give it up in the event that you accidentally drop it in water or forget to remove it from your pants pocket.

Remove the battery first. Clean the electronic chip with isopropyl alcohol or a similar product and dry it completely before replacing the battery. Then try the fob and check if it functions. If the key still doesn't function, it may need to be programmed again. This is usually handled by an auto locksmith or dealer.

If the key is older and has not been programmed to your car It will most likely need to be replaced completely. This is a simple procedure that can be handled by a professional automotive locksmith. The locksmith will need the key to be cut to match the car's ignition. The locksmith also needs to reprogram your fob into the car's system. This is a quick and affordable process which can be completed in the same day.

Receiver Module Issues

Your 500 key fob may not work because it's out of range. The remote typically has a range of 30 feet or less and if it's far from your vehicle, it will not respond to your commands. It can be solved by moving it closer to your vehicle until it starts responding.

If you've replaced the battery in your coin (commonly known as a "button" or "watch") and the fob isn't working It could be because of an internal circuit board issue. Reprogramming your fob can resolve this issue. The instructions are available for most vehicles on YouTube or in the owner's guide.

It is possible to replace the metal clips that keep the coin battery in place. If they loose tension, it may prevent your battery from sitting properly, causing your remote to malfunction.

In rare instances, the fob might be out of connection with your vehicle as a result of hardware or software issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances, they may need to reinstall the software on your body control module too.

Interference

Interference can also cause the key fob to be unable to receive or transmit signals. This can occur when the key fob is in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob could not work because of a weak connection with the buttons or water damage, or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. replacing the battery, reprogramming, and using the spare key fob, you could have a damaged receiver module on your 500. The receiver module is situated under the dash, and it picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands that are then interpreted by the vehicle.

There's a quick and easy way to reset the 500's internal system, including the keyfob. Disconnect the 12 volt battery for about 15 minutes, by taking off the negative cable first then the positive cable. Reconnect the battery. This will remove any residual electricity and restart the car's computers. This can help you get your key fob working again. If the issue continues, you should seek out an expert technician. They'll be able to diagnose the exact cause of your problems.